HotStarTaq Master Mix Kit
For highly specific amplification for any PCR application
For highly specific amplification for any PCR application
Cat. No. / ID: 203446
Each lot of HotStarTaq Master Mix Kit is subjected to a comprehensive range of quality control tests, including a stringent PCR specificity and reproducibility assay in which low-copy targets are amplified. HotStarTaq Master Mix Kit outperformed kits tested from other suppliers and ensures high specificity and superior performance in hot-start PCR (see figures " Higher specificity with different primer–template systems" and " Superior performance " and table). The innovative PCR buffer provided with the kit ensures specificity over a wide range of PCR conditions, minimizing the need for optimization (see figure " Tolerance to variable temperatures and magnesium concentrations").
The combination of high specificity and easy handling makes the HotStarTaq Master Mix Kit suitable for use with complex genomic or cDNA templates (see figure " Effect of hot start on RT-PCR performance"), multiple primer pairs (see figure " Specific amplification in multiplex PCR"), and templates isolated from difficult sources or very low-copy targets (see figure " Highly sensitive single-cell PCR"). It is also suitable for projects such as genetic screening, in which large numbers of samples are amplified.
Concentration: 5 units/µl
Recombinant enzyme: Yes
Substrate analogs: dNTP, ddNTP, dUTP, biotin-11-dUTP, DIG-11-dUTP, fluorescent-dNTP/ddNTP
Extension rate: 2–4 kb/min at 72°C
Half-life: 10 min at 97°C ; 60 min at 94°C
Amplification efficiency: ≥105 fold
5'–>3' exonuclease activity: Yes
Extra A addition: Yes
3'–>5' exonuclease activity: No
Contaminating nucleases: No
Contaminating RNases: No
Contaminating proteases: No
Self-priming activity: No >
HotStarTaq Master Mix is a ready-to-use mixture of HotStarTaq DNA Polymerase, QIAGEN PCR Buffer, and dNTPs. HotStarTaq DNA Polymerase, a modified form of Taq DNA Polymerase, provides high specificity in hot-start PCR.
HotStarTaq DNA Polymerase is supplied in an inactive state and has no polymerase activity at ambient temperatures. This prevents extension of nonspecifically annealed primers and primer dimers formed at low temperatures during PCR setup and the initial PCR cycle (see figures " Superior performance in hot-start PCR" and "Higher specificity with different primer–template systems"). HotStarTaq DNA Polymerase is activated by a 15-minute incubation at 95°C, which can be incorporated into any existing thermal-cycler program.
QIAGEN PCR Buffer maintains specific amplification in every cycle of PCR by promoting a high ratio of specific-to-nonspecific primer binding during the annealing step in each PCR cycle (see figure " Increased specificity of primer annealing"). Owing to a uniquely balanced combination of KCl and (NH4)2SO4, the buffer provides stringent primer-annealing conditions over a wider range of annealing temperatures and Mg2+ concentrations than conventional PCR buffers. Optimization of PCR by varying the annealing temperature or the Mg2+ concentration is therefore often minimal or not required (see figures " Wide annealing temperature window" and " Tolerance to variable magnesium concentration").
HotStarTaq Master Mix Kit is highly suitable for a wide variety of applications, including challenging applications such as amplification of:
The HotStarTaq procedure is fast and easy for maximum convenience.
|Applications||PCR, RT-PCR, Complex genomic templates, very low-copy targets|
|Real-time or endpoint||Endpoint|
|Enzyme activity||5'-> 3' exonuclease activity|
|Sample/target type||Genomic DNA and cDNA|
|Single or multiplex||Single|
|Reaction type||PCR amplification|
|With/without hotstart||With hotstart|
Both the quality and quantity of nucleic acid starting template affect PCR, in particular the sensitivity and efficiency of amplification. PCR sensitivity and efficiency can be reduced by the presence of impurities in nucleic acid preparations or in biological samples. These PCR inhibitors are completely removed when template is prepared using QIAGEN Kits for nucleic acid purification. Please refer to the Brochure "Maximizing PCR and RT-PCR success" for additional information.
The optimal primer–template ratio has to be determined empirically. If too little template is used, primers may not be able to find their complementary sequences. Too much template may lead to an increase in mispriming events. Generally, no more than 1 ug of template DNA should be used per PCR reaction. As an initial guide, spectrophotometric and molar conversion values for different nucleic acid templates are listed below.
Spectrophotometric conversions for nucleic acid templates
|1 A260 unit*||Concentration (ug/ml)|
*Absorbance at 260 nm = 1
Molar conversions for nucleic acid templates
|1 kb DNA||1000 bp||1.52||9.1 x 1011|
|pUC 19 DNA||2686 bp||0.57||3.4 x 1011|
|pTZ18R DNA||2870 bp||0.54||3.2 x 1011|
|pBluescript II DNA||2961 bp||0.52||3.1 x 1011|
|Lambda DNA||48,502 bp||0.03||1.8 x 1010|
|Average mRNA||1930 nt||1.67||1.0 x 1012|
|Escherichia coli||4.7 x 106*||3.0 x 10-4||1.8 x 108**|
|Drosophila melanogaster||1.4 x 108*||1.1 x 10-5||6.6 x 105**|
|Mus musculus (mouse)||2.7 x 109*||5.7 x 10-7||3.4 x 105**|
|Homo sapiens (human)||3.3 x 109*||4.7 x 10-7||2.8 x 105**|
* Base pairs per haploid genome
** For single-copy genes
PCR products that will be cloned using the QIAGEN PCR Cloning Kit should be generated using a thermostable DNA Polymerase without proofreading activity, such as Taq DNA Polymerase. Such polymerases attach a single A overhang to their reaction products, which can hybridize to the U overhang of the pDrive Cloning Vector. For efficient addition of an A overhang during the PCR procedure, we recommend a final extension step for 10 min at 72°C as described in the standard protocols of the Taq PCR- and HotStarTaq PCR handbook.
Not necessarily. In a lot of cases, the uniquely formulated PCR Buffer provided in the HotStarTag Plus DNA Polymerase, HotStar HiFidelity Polymerase, Taq DNA Polymerase, HotStarTaq DNA Polymerase, and QIAGEN Multiplex PCR Kits provides optimal amplification of specific PCR products. The usefulness of Q-Solution needs to be determined empirically for each primer/template setup, by running parallel PCR reactions with and without Q-Solution under the same cycling conditions.
Q-Solution changes the melting behavior of DNA and will often improve a suboptimal PCR caused by templates that have a high degree of secondary structure or high GC-contents. For more details on the effects of Q-Solution on PCR amplification, please see the Q-Solution sections of the HotStarTag Plus DNA Polymerase, HotStar HiFidelity Polymerase, Taq DNA Polymerase, HotStarTaq DNA Polymerase, and the QIAGEN Multiplex PCR Handbooks.
Yes, please follow either of the User-Developed Protocols:
Yes. Please see Table 3 in our brochure Maximizing PCR and RT-PCR success. We tested the effects of different inhibitory substances in a number of PCR systems. We also analyzed the effect of including different volumes of reverse transcription (RT) reaction mixtures in PCR. Please see the table below for a list of commonly encountered template impurities and their inhibitory effects on PCR.
Impurities showing inhibitory effects on PCR
|Sodium Acetate||≥5 mM|
|Sodium Chloride||≥25 nM|
|RT reaction mixture||≥15%|
The DNA yield obtained in a PCR reaction depends on the size of the amplicon, design of the primers, starting amount of template and primers, amplification efficiency, reaction volume, numbers of PCR cycles etc. Therefore it is really difficult to predict what yield to expect. Nevertheless, in our experience, approximately 1 µg is a good guess for most cases.
To determine the optimal annealing temperature for a PCR assay, a Temperature Gradient experiment should be performed. To do this, you will set up several PCR reactions in duplicate for the same primer/template combination, using the same PCR chemistry, and subject each of the reactions to a slightly different annealing temperature within a specified range. If a thermal cycler with a temperature gradient function can be used, you can simply program a temperature range for adjacent wells in the cycling block. If no cycler with a gradient function exists in your lab, you will either have to perform duplicate reactions at different temperatures in different machines (if available), or back to back in the same machine.